WAX OPERATOR B
: Job Details :

BASIC QUALIFICATIONS:* High School Diploma or GED from an accredited institution.* Employees must be legally authorized to work in the United States. Verification of employment eligibility will be required at the time of hire. Visa sponsorship is not available for this position.* This position entails access to export-controlled items and employment offers are conditioned upon an applicant's ability to lawfully obtain access to such items.PREFERRED QUALIFICATIONS:* Basic Computer skills.MUST BE ABLE TO WORK 12 HOUR ROTATING NIGHT SHIFTS, 7:00 P.M TO 7:00 A.M. (2 on 2 off, 3 on 2 off, 2 on 3 off)JOB SUMMARY:Wax Cell Operators B's are responsible for the following skills: pattern inspection, pattern sub-assembly, mold assembly, including gating into finished molds, pinner/robot, engraving. Trainees must successfully complete written and practical assessment of skills/knowledge at end of skills training.Essential Functions* Basic Computer Skills* Must be able to read and interpret Product Criteria (PC) and Activity Instructions (AI).* Must be able to function as a member of a team and be able to work under general supervision.* Must be able to maintain expected quality levels.* Comply with all site required policies and procedures including but not limited to: EHS, Quality, Code of Conduct and the Wichita Falls Employee Handbook.JOB RESPONSIBILITIES:1. Performs inspection of all patterns and decides to accept, repair or scrap the part per documented instructions.2. Follows established protocol for notification of potential deviations or scrap trends.3. Performs set-up of dimensional gauges.4. Dimensionally inspects cores and wax patterns using supplied gauging to specified tolerances.5. Utilizes the necessary fixturing or gauges to assure dimensional conformance of the pattern/mold to specified tolerances.6. Prepares sprues as required and locates ceramic bracing per engineering specifications.7. Attaches the pattern to the gating and seals per the specified method.8. Performs seal operations as specified.9. Performs dip seal operations as specified ensuring that the gates are sealed on the mold but are not over dipped.10. Performs sub-assembly of multiple airfoil patterns.10. Responsible for the quality of the entire mold assembly11. Torch sprues, seal and pour cup. Add bracing as required per engineering specifications.12. Sets up equipment as required to perform specific activitiesPerforms all operations associated with pinner/robot.13. Must pay close attention to detail.14. Maintains necessary supplies for the area to maximize productivity.15. Performs other duties as required.16. Complies with all EHS rules related to the work environment.17. Works OT as needed.18. Follows 5S rules and procedures.19. Utilize help chain when needed. (Human Performance, BOLO)ENVIRONMENTAL HEALTH AND SAFETY RESPONSIBILITES:* Comply with all department, facility, corporate and regulatory EHS regulations* Wear all required personal protective equipment (PPE). Requires wearing safety glasses, gloves and Metatarsal shoes.* Report all job-related illness and injuries (Per Employee Handbook).* Report all safety, health and environmental concerns to your supervisor in a timely manner.* Attend all EHS training.PHYSICAL DEMANDS/EQUIPMENT USEDPhysical Demands:The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.Employee is required to execute the following:* Stair climbing.* Reaching near, far and overhead.* Pushing pulling, twisting and handling.* Be able to lift from floor-to-waist, waist-to-chest and chest-to-overhead* Be able to finger press, use a keyboard, mouse and tolerate hand/arm vibration* Gripping and Pinching* Carry items with two hands.* Carry items with one hand.* Work requires moderate physical effort including prolonged standing.* Squatting/crouching/bending when retrieving stored items from lower shelves, moving equipment and product inspections.* lifting >5 Lbs.* Must pass Jaeger I eye exam.Equipment Used:* Injection Machine* Hot Plates* Hand tools* Engraving Machine* X-Ray Unit* Gauging FixturesWork Environment:* Works in air-conditioned area.* Slight exposure to chemicals, fumes, oil, dust, noise and heat or coldMEDICAL SURVEILLANCE REQUIREMENTS:* Vision